Warehouse & Industrial Epoxy Flooring in Abbotsford
Epoxy flooring for warehouses, service bays and manufacturing plants starts with the slab, not the topcoat. We assess the concrete, specify a system matched to the chemical and traffic load, prep the surface to manufacturer spec, and install primer, body coat, aggregate and topcoat as a complete system. Abbotsford Concrete backs every install with a written estimate and a firm schedule.
Most commercial epoxy failures trace back to one source: the concrete underneath was not ready. A slab with moisture, contamination, uneven surface or old coating residue will reject the epoxy system no matter how good the material is. The concrete is the base; the epoxy is the wear layer.
Our process begins with the slab. We diamond-grind to the system's required profile, test for moisture vapor, fill cracks and joints with compatible material, and apply a moisture-mitigation primer where needed. Only then does the body coat and topcoat go down. Aggregate is added where slip resistance is part of the spec.
We evaluate the slab condition, understand the use case (wash-down, chemical exposure, traffic type), and specify the epoxy system, primer, body coat, aggregate and topcoat that will perform in that environment.
Grind and prepare
The slab is diamond-ground to the system's prep profile, removing old coatings, contaminants and surface laitance. Moisture testing determines if a vapor-mitigation primer is needed before the epoxy goes on.
Prime and build
Primer is applied to bond the epoxy to the concrete, the body coat is applied at the specified thickness, and aggregate is broadcast into the wet coat where slip resistance is required.
Seal and return
The topcoat is applied to seal the system and create the wear surface. The floor cures on the manufacturer's schedule, and we hand it back ready for traffic at the timeline we quoted.
System selection is critical
Choosing the Right Epoxy System for the Job
Epoxy systems vary widely in chemical resistance, abrasion rating, temperature tolerance and slip properties. A food-processing plant needs a different system than a service garage, which needs a different system than a warehouse. Specifying the wrong system for the use case means failure in months, not years, even if the install is perfect.
We build the spec around the actual environment: hot tires and automotive fluids for service bays, wash-down and food-grade compliance for processing plants, heavy forklift traffic for warehouses. Where the epoxy floor adjoins polished concrete in office areas or loading dock concrete outside, we coordinate the systems so they transition cleanly.
Slab prep, chemical resistance, slip ratings and what makes epoxy the right choice for commercial spaces.
A properly specified and installed system lasts the better part of a decade or longer in most commercial environments. Wear comes from traffic and chemicals; the system spec determines how it handles each. We size the spec to your use.
Diamond grinding to the manufacturer's prep profile is our standard, removing contaminants, old coatings and surface laitance. Where moisture testing flags a high-vapor slab, a moisture-mitigation primer goes on first. Skipping prep is why coatings fail.
Yes, with the right system spec. Wash-down floors get a system with chemical resistance and slip aggregate; food processing gets a system rated to that environment; service garages get a system rated for hot tires and automotive fluids. The system matches the use.
Foot traffic typically a day after the topcoat; full vehicle or chemical service later in the cure schedule. We give you a clear return-to-service timeline before the install so you can plan production around it.
Sometimes, but usually we remove the failed system back to clean concrete first. Installing over a failing layer just inherits its failure mode. The honest scope often includes removal as a line item; the quote tells you up front.
Client reviews
What Abbotsford Operators Say About Their Epoxy Floors
Three contractors quoted slab prep as a paint roller and a primer. Abbotsford Concrete quoted diamond grinding and explained why. Two years in, floor is still tight to the slab, no peeling.
Z. R.
Warehouse Manager, Abbotsford
★★★★★
Service-bay system rated for hot tires and automotive fluids. Wash-down works, no spalling at the floor drains, and the slip aggregate is doing its job in winter.
Q. U.
Service Garage Owner, Chilliwack
★★★★★
They specced the system to the actual chemical exposure in our plant, not the cheapest option that fits the budget. Worth every dollar; the previous floor had failed in 14 months.
X. U.
Manufacturing Plant Manager, Mission
★★★★★
Coordinated install around our shift schedule. Floor was returned to service at the timelines they quoted, no surprises, no slipped delivery dates. Real professionals.
W. U.
Operations Director, Langley
From the blog
Concrete Guides & Articles
Practical reading on planning, finishes and caring for concrete in Abbotsford.
Describe the space, the use case, and the chemical or traffic exposure. We will visit the site, specify the right system, and send a written quote within one business day.
foundations
Cost & Planning