Patched, worn, or discoloured concrete slabs don't need to be torn out. A micro-topping bonds a thin polymer layer to the existing slab, creating a fresh, seamless surface ready for any finish. Abbotsford Concrete handles the prep, application and cure. Free written estimate on every project.
Not every concrete slab can be polished or stained directly. Patches, inconsistent surfaces, and cosmetic damage make the existing slab unsuitable as a finished floor. Rather than remove and replace the entire slab, a micro-topping overlay bonds a thin, smooth layer to the top.
The polymer-modified topping is applied in thin passes, each one building on the last until you have a uniform, sound surface. Once cured, that new surface accepts polished finishes, stained colour, or sealed protection. The slab below stays in place, saving time and cost.
Micro-topping is not a fix for structural issues. If the slab is heaving, has deep moving cracks, or base failure, the slab itself must be replaced. We assess the concrete and tell you whether the topping will work or if tear-out is necessary.
Recent work
Installation sequence
Applying Micro-Topping to Your Abbotsford Floor
Inspect and plan the substrate
We examine the slab for structural soundness, identify any cracks or repairs needed, test for moisture, and confirm what finish will go on top of the topping.
Mechanically profile and prime
The slab surface is ground to open the pores and create mechanical bond, repaired where needed, then primed with the topping system's specified primer.
Trowel topping in thin layers
The polymer-modified topping is applied in multiple thin passes, each one tightly bonded to the substrate, building a smooth, even new surface.
Burnish, finish and cure
The topping is burnished to the desired sheen, then cured per schedule before polish, stain or sealer is applied on top.
Finishing options
Topping Ready for Polish, Stain or Sealed Finish
The micro-topping itself is not the final floor. It is the base layer that makes a finished floor possible. Most homeowners choose to polish the topping for a bright, hard-wearing surface that shows off the concrete.
Others prefer stained colour layered into the topping, then sealed for warmth and protection. Some simply seal the topping for a clean, matte look. The topping bonds equally well to all three finishes and works seamlessly with radiant floor heating systems when warmth is part of the plan.
Thickness, when it works, what finishes pair with it, and what it cannot fix.
A few millimetres total, applied in lifts. It is not a full overlay; it is a thin resurfacing that bonds to the substrate and gives the next finish a clean canvas.
When the slab has structural problems, heaving, deep cracks that move, base failure. The topping fixes a cosmetic-grade slab problem, not a structural one. We assess the slab and tell you straight which side of the line it is on.
Any of the interior finishes we install, polish, stain, or a clear sealer. The topping is engineered to take them all.
Done properly, no. The lifts blend together and the burnish produces a uniform surface. We pre-test on a sample area for tricky finishes to confirm the look before doing the whole floor.
Yes. Heated floor underlayment goes down first to encase the radiant heat tubing, then the micro-topping over it, then the finish above. The whole stack works as one heated floor system.
Homeowner reviews
What Abbotsford Homeowners Say About Micro-Topping Floors
Old basement slab was patched and ugly. They micro-topped it then polished, and now it reads as a brand-new floor without the tear-out and mess of a replacement.
H. B.
Abbotsford
★★★★★
Saved us a slab replacement on the main floor. Micro-topping plus stain plus seal gave us exactly the look we wanted, and the existing slab is hidden underneath.
M. L.
Chilliwack
★★★★★
Knew the answer when they walked in, micro-topping was the move because of how patched our slab was. Done in less than a week and the new floor looks seamless.
P. O.
Langley
★★★★★
Combined with heated floor underlayment underneath. The radiant heat warms the topping evenly and the finished floor is exactly the same look top to bottom.
U. E.
Mission
From the blog
Concrete Guides & Articles
Practical reading on planning, finishes and caring for concrete in Abbotsford.
Tell us about the room, the slab condition, and the finish you want. We will assess the concrete, confirm the topping is the right move, and send a written quote within one business day.
foundations
Cost & Planning