Uneven slabs stop most floor finishes before they start. Self-leveling compound spreads across the substrate, settles flat under gravity, and cures into a sound base ready for tile, plank, polish or micro-topping. Abbotsford Concrete measures the slab, primes it, pours the leveler, and hands you a flat floor. No shimming. No lippage. No telegraphing.
A slab that dips and rises will crack tile, show lippage in plank, telegraph through polish, and reject micro-topping. The finish is only as good as the substrate it sits on. Self-leveling concrete fixes the substrate before the finish ever goes down.
The process is straightforward. We prime the slab with a manufacturer-matched primer, mix the self-leveling compound to spec, pour it onto the floor, and let gravity do the work. The compound flows to the low spots, settles level, and bonds chemically to the primed surface below.
Once cured, the new surface is flat, sound, and ready. Epoxy, polished concrete, stain, micro-topping, or tile all go down on a slab that is actually flat enough to take them.
Recent work
The sequence
How Self-Leveling Pours Get Done in Abbotsford
Measure and assess the substrate
We check moisture, identify high and low spots, and confirm the slab is sound. We pick the self-leveling product and primer matched to the substrate type (concrete, plywood, or existing tile).
Mark elevation and contain edges
We mark the target finished height, set perimeter dams so the leveler stays where it should, and apply the manufacturer-matched primer to the entire floor.
Mix, pour, and smooth to mark
The self-leveling compound is mixed to the published water ratio, poured onto the primed substrate, and gently raked or smoothed to the marked elevation. Gravity handles the rest.
Cure and prepare for finish
The compound sets to walkable in hours and cures fully over the manufacturer's window. The new surface is flat, bonded, and ready for whatever finish comes next.
Common applications
When Leveling Compound Becomes Essential
Renovation floors are the biggest use case. Old slabs, patched slabs, and slabs in older buildings rarely meet the flatness modern finishes require. Self-leveling turns them into a usable substrate without a full tear-out.
It also sits under radiant heat systems as part of the underlayment stack, under polished concrete when the slab is not polish-ready, and under micro-topping when extra fill is needed. The flatness is what every system above depends on to perform.
When you need it, what it bonds to, thickness and finishes above in Abbotsford.
Not always. If the substrate is already within tolerance for the finish you want, self-leveling is unnecessary. We measure first; if the dips and humps fall outside what the finish can handle, self-leveling is the honest fix.
All three, with the right primer and product for the substrate. We pick the matched primer and self-leveling product for what the floor sits on, so the bond is engineered for the surface, not assumed.
Most products handle up to about an inch in a single pour, more in lifts with proper bonding. We size the pour to the substrate's worst dip and the finish's flatness requirement.
No, it is a finishing prep, not a structural floor. It bonds to a sound substrate and brings it flat. If the slab below is structurally compromised, that has to be fixed first.
Walkable in a few hours, ready for tile or plank typically the next day, ready for polishing or staining once fully cured to the manufacturer's published window. We give you the exact timeline on the project.
Homeowner reviews
What Abbotsford Homeowners Say About Their Self-Leveling Pours
Old kitchen slab was a wave. Self-leveling brought it dead flat and the tile went down without a single shim. The result looks like a brand-new build.
G. R.
Abbotsford
★★★★★
Polished the basement floor after a self-leveling pour. The polish was perfect because the substrate was actually flat for the first time.
V. D.
Maple Ridge
★★★★★
Plywood substrate in our addition. They primed it properly and the leveler bonded so well I forgot it was on plywood. The plank floor sits perfect.
O. B.
Mission
★★★★★
Heated floor underlayment plus self-leveling plus micro-topping plus polish. Whole stack done in sequence and the finished floor is dead flat with even radiant heat.
I. U.
Langley
From the blog
Concrete Guides & Articles
Practical reading on planning, finishes and caring for concrete in Abbotsford.
foundations
Cost & Planning